Eleventh week
For this last week we must fulfill a huge workload. my coworker and I must arrange meeting with other coworkers from Salesianos and get to an agreement to go forward in every single tasks which was assigned through the week. Next a working plan is going to be shown:
Taking a look at the document on the right side, we can easily notice that there are several milestones which are required to be presented in a specific day or week.
As we can realize there are some quite outstanding tasks to fulfill each day of the week.
On december 17th, We are engaged to provide all blueprints relating to our project.
On december 18th, We are engaged to provide our final technical report which must contain all the stages of the project from the beginning up to the last steps and arragements that my coworkers and I have done. Inside this final document must have all the points that our professors from both schools have assigned.
On december 19th, we will have to speak about our final outcome in from of both schools (Maristak- Salesianos). To give our final speech, we will use the media or a specific type of telecommunication.
On january 9th, my coworker ( from Maristak) and I will defend our proposal and tell why this should be taken into account to be manufactured. On the other hand, we must explain why we have selected specific heat treatments and their advantages.
Starting the week, my coworkers and I had a big delay linked to the delivery of a specific task from the last week, We could not deliver our 3D pieces on time, because we didn't have a good communication between us. After dealing with this kind of throubles, we must have gone forward and half part of our group had to draw blueprints and the another one had to carry on writing our final report down and make a small presentation for our final speech. A day before final presentations, we concluded with the majority of our deliveries. Finally we had to focus on finishing our final report which contained several mistakes.
The last milestone came, all of us were quite nervous about this, We had no clue about how to start giving our speech, and we knew that all professors were engaged to score us. After some minutes all of us organized our turns to provide the speech and finally it turned out quite fine. Most of the group extended their speech, but we decided to provide it to the public in only 5 minutes, perhaps it was not a quite good idea, but our professors told us about it, they said: "Each speech must only last 5 minutes no more because there are a hugh amount of groups", so we fulfilled their requirement.
1) Descritptive memory
Inside this document we delivered the following points:
- Identification of troubles to be treated
- Proposal from each one of us in order to solve defined troubles.
- Selection of best proposals among us, or enhance a specific proposal in order to fulfill it with the parameters which were specified beforehand.
- Drawings from the selected sketch and prepare 3D and 2D models by using software engineering applications such CATIA V5 and SolidWork 2019.
- Bill of material (BOM), where the teamwork must specify all elements which were used to complete our project.
- Scheduled and programmed plans which were used to accomplish every single milestone.
- Working plans and documents where must show all agreements that the teamwork has engaged.
1.1) Documents to be presented
On december 19th, we will have to speak about our final outcome in from of both schools (Maristak- Salesianos). To give our final speech, we will use the media or a specific type of telecommunication.
On january 9th, my coworker ( from Maristak) and I will defend our proposal and tell why this should be taken into account to be manufactured. On the other hand, we must explain why we have selected specific heat treatments and their advantages.
Starting the week, my coworkers and I had a big delay linked to the delivery of a specific task from the last week, We could not deliver our 3D pieces on time, because we didn't have a good communication between us. After dealing with this kind of throubles, we must have gone forward and half part of our group had to draw blueprints and the another one had to carry on writing our final report down and make a small presentation for our final speech. A day before final presentations, we concluded with the majority of our deliveries. Finally we had to focus on finishing our final report which contained several mistakes.
The last milestone came, all of us were quite nervous about this, We had no clue about how to start giving our speech, and we knew that all professors were engaged to score us. After some minutes all of us organized our turns to provide the speech and finally it turned out quite fine. Most of the group extended their speech, but we decided to provide it to the public in only 5 minutes, perhaps it was not a quite good idea, but our professors told us about it, they said: "Each speech must only last 5 minutes no more because there are a hugh amount of groups", so we fulfilled their requirement.
What has to be presented inside our technical report and final speech?..... Now I am going to make a summary about all aspects that must be presented in the last stage of this challenge:
Inside this document we delivered the following points:
- Identification of troubles to be treated
- Proposal from each one of us in order to solve defined troubles.
- Selection of best proposals among us, or enhance a specific proposal in order to fulfill it with the parameters which were specified beforehand.
- Drawings from the selected sketch and prepare 3D and 2D models by using software engineering applications such CATIA V5 and SolidWork 2019.
- Bill of material (BOM), where the teamwork must specify all elements which were used to complete our project.
- Scheduled and programmed plans which were used to accomplish every single milestone.
- Working plans and documents where must show all agreements that the teamwork has engaged.
1.1) Documents to be presented
On the right side there is a sample of type of documents that must be presented inside the technical report. In this case the document on the right is called " Meeting report", inside this document is registered all activities relating to tasks from each day. It was a completely reliable document to organize our work every single day in this period of time.On the other side, meeting reports must be included inside our final descriptive memory in the last part of it, specifically in annexes.
As we can see, there is a document which are located below on the right side, and it is named "Working plan", here one member of our group had the mission to complete and register all tasks through the entire weeks. This document was essential to go step by step through all our project. In the first lines it has a summary of all troubles which were treated, and some pictures of it.On the other hand, this report must have be included by all groups from both schools.This was included in the last chapter of our report which was called "Annexes".
1.2) 3D and 2D models
In this subsection we drew our main ideas to solve all troubles through CATIA V5 and SolidWorks 2019. Fortunately we already have some training using those software so we could accomplish our tasks linked to this subsection. Nex some 3D and 2D models will be described:
In this subsection we drew our main ideas to solve all troubles through CATIA V5 and SolidWorks 2019. Fortunately we already have some training using those software so we could accomplish our tasks linked to this subsection. Nex some 3D and 2D models will be described:
1.2.1) Tool holder subassembly
The major function of this element is to hold all cuting elements which count with a hugh amount of differents cross-sections. It is composed of 16 components among scews, springs and solid pieces of metal.
On the left side, we can see the entire body of the assembly, yellow screws (commercial elements) help to press the cutting element through a small rectangular metal plate. When it's needed to return to its original position then we have to unscrew it and some springs help to do it in an easily and constant way.
1.2.2) Turret subassembly
This assembly is composed of 6 components and those are attached mechanically each other. The main purpose of this set is to hold and lock our tool holder which was seen before. There is a handle which is joined to an eccentric bushing which makes possible move 2 drums which are located in the cube sidelong.Two drums are activated by the eccentric bushing when it turns around the axis of the central screw which belongs to the lathe and lock the tool holder by pressing it.
1.2.3) 2D blueprints
In this part we are going to show some samples of 2D blueprints which were drawn by both groups (Salesianos and Maristaks). This point is pretty essential because through these blueprints fabricators will lead themselves to accomplish this purpose. Next some samples of 2D blueprints:
1.2.3) 2D blueprints
In this part we are going to show some samples of 2D blueprints which were drawn by both groups (Salesianos and Maristaks). This point is pretty essential because through these blueprints fabricators will lead themselves to accomplish this purpose. Next some samples of 2D blueprints:
No hay comentarios:
Publicar un comentario